Zennox 66-LED Solar Sensor Light
Now Just: £19.99
- Solar powered; No wires or expensive running costs, this light works by simply using sunlight
- PIR movement detection; When motion is detected a light is triggered and remains on for 15-30 seconds to discourage intruders
- Long range; The PIR system has a range of 9 metres and features 66 bright LED lights
- Weather resistant; The solar light is encased in weather-resistant casing allowing it to be kept outdoors all year round
- Guarantee; 12-month guarantee
Zennox 66-LED Motion Sensor Light
Keep pathways, steps and alleyways visible at night with the help of this solar panel powered, 66-LED motion sensor light. Perfect for increasing your night-time visibility for you and your guests, it also works as a deterrent to potential intruders.
This security light has no overheads or running costs, instead taking its power from the solar panel on the top of the unit and recharging throughout the day. It is encased in a weather-resistant casing so it’s functional in all weather conditions, great for dark, wet nights.
This light comes fitted with a motion sensor that will automatically light up whenever you're within nine metres of it thanks to its PIR (infrared) movement detection. The LEDs have an eight-hour working time after a full charge.
Three lighting modes:Mode 1: Will automatically illuminate when motion is detected after darkness.
Mode 2: Will automatically illuminate with a bright light when darkness falls, will then switch to a brighter light when motion is detected.
Mode 3: Will automatically illuminate with a dim light when darkness falls and will stay on for 4-6 hours if fully charged.
Note: The solar panel must be placed in a well-lit location for maximum sunlight absorption. Anything that shades the panel will affect the brightness and lighting duration. At least six hours of sunlight is required for the lights to illuminate. Remember! During winter months charging time will be affected due to the limited daylight hours.
Dimensions: L17 x W10.5 x H.9cm
G4327 – 66-LED solar sensor light
Delivery InformationDelivery on this product is available to most UK Mainland addresses.
We take every care to ensure that you receive the correct goods in perfect condition. In the unlikely event that you ever need to return any item to us and it is within our 30-day warranty period then please contact us for a returns authorisation number. Our customer service team will then provide you with our returns address.
All goods must be returned via recorded, insured method at your own cost. We cannot be held responsible for returns parcels lost in transit. It is the sender's responsibility to ensure parcels are adequately insured. If the goods exceed Â£46 in value we strongly suggest that you take out additional insurance. In order that we can satisfy your requirements promptly we will need your full instructions, explaining the reason for the return and the action you wish us to take.
Natural Wood Characteristicts
As wood is a natural material it may be affected by the following:
Shrinkage & Warping
The timber used in the construction of your garden building will have retained some of its natural moisture content. The moisture content of the timber will vary, depending upon prevailing environmental conditions, which will result in the components either naturally expanding or contracting. As the components dry out shrinkage may occur. A good waterproofing treatment from the start is the best protection to minimise the effect of moisture loss/intake.
Damp & Mould
During the winter months, cold and damp conditions can result in an increased amount of moisture within your garden building, especially when used infrequently. Condensation can form on the timber and other items stored within your garden building. If left this moisture is likely to cause mould and mildew. To prevent the build-up of moisture, we recommend leaving the door or windows of your building open from time to time, to allow the fresh air to circulate. We also advise against storing wet or damp items in your garden building as this will also increase the level of moisture in the building. If mould or mildew does start to form within your building we recommend using an anti-mould cleaner to remove it and to prevent it spreading, which if left untreated could permanantly damage your garden building.
Splits, Cracks & Knots
Small splits and cracks in some components or holes may appear where knots shrink and fall out. This will not affect the structure of your garden building however if you wish to fill them this can be easily done using any good quality wood filler
Sap is naturally occurring in wood and may appear in some boards of your garden building. If you wish to remove the sap, we advise waiting until it is dry and then using a sharp knife to carefully remove it. If the removal of the sap causes a hole in the timber, we recommend using a good quality wood filler to fill it.
Please be aware that these are natural timber characteristics which in most cases will not impact the structure or function of the garden building, therefore are not considered as product defects (as outlined within our Terms & Conditions). If you require further advise or information please contact our friendly Customer Services Team.